# CDL Air Brakes and Combination practice test

15 free CDL Air Brakes and Combination questions from Clinched, each with the official source.

## 1. You are driving when the air pressure falls below the warning level and stays there. How must the low air warning behave?
- A. It stays on the whole time pressure is low
- B. It sounds once and then shuts itself off
- C. It works only while you press the brake pedal

Answer: A. Federal rules require the low air warning to give a continuous warning for as long as reservoir pressure is at or below the warning level. A warning that beeps once and stops, or one that works only while you brake, would not meet that requirement.
Source: 49 CFR §393.51 Warning signals, air pressure and vacuum gauges., “(2) A warning signal that is audible or visible to a person in the normal driving position and provides a continuous warning to the driver whenever the air pressure in the service reservoir system is at 379 kPa (55 psi) and below, or one-half of the compressor governor cutout pressure, whichever is less.”

## 2. You are going down a long, steep grade. What role should your service brakes play?
- A. They add to the slowing done by the engine
- B. They do all of the slowing while the engine idles
- C. They do most of the slowing, helped by the engine

Answer: A. On a long or steep downgrade, engine braking is the main way to slow down. The service brakes only add to it. If you make the brakes the main source of slowing, they overheat and fade.
Source: CDL Manual (AAMVA model, March 2025), Section 5.4.6 Proper Braking Technique, “”

## 3. While you fan down the air during an inspection, the parking brake valve pops out. What happens to the brakes at that moment?
- A. The service brakes fully release
- B. The brakes stay as they were
- C. The spring brakes come on

Answer: C. When the valves close because of low pressure, the spring brakes apply. This is the safety backup that holds the vehicle when air runs low. The brakes do not release, and nothing staying the same would defeat the purpose of the valve.
Source: CDL Manual (AAMVA model, March 2025), Section 5.3.3 Step 7 Final Air Brake Check, “”

## 4. Your truck uses spring brakes as its parking brakes. What does their stopping and holding power depend on?
- A. How much air is in the tanks
- B. How warm the brake drums are
- C. How well the brakes are adjusted

Answer: C. Spring brakes get their force from springs, and that force only reaches the drums properly when the brakes are in adjustment. Tank air pressure is what releases spring brakes, not what applies them. Drum temperature is not what determines spring brake power here.
Source: CDL Manual (AAMVA model, March 2025), Section 5.1.14 Spring Brakes, “”

## 5. You are climbing into a late-model tractor with air brakes for the first time. What does the parking brake control most likely look like?
- A. A red, eight-sided push-pull knob
- B. A yellow, diamond-shaped push-pull knob
- C. A blue, round toggle switch

Answer: B. On newer air-brake vehicles, the parking brake control is a yellow knob shaped like a diamond that you push or pull. The red eight-sided knob is a different control, and parking brakes are not set with a blue toggle switch.
Source: CDL Manual (AAMVA model, March 2025), Section 5.1.15 Parking Brake Controls, “”

## 6. Where can an air compressor get the oil that lubricates it?
- A. Its own supply or the engine oil
- B. Alcohol fed in by the evaporator
- C. Oil that settles in the air tanks

Answer: A. A compressor is lubricated either from its own oil supply or from the engine's oil. Oil found in the bottom of an air tank is contamination that must be drained out, not a lubricant source. Alcohol is added only to reduce icing.
Source: CDL Manual (AAMVA model, March 2025), Section 5.1.1 Air Compressor, “”

## 7. You are learning about the dual air brake system on your tractor. How is air stored and carried in each of the two systems?
- A. Each system has its own tanks, hoses and lines
- B. The secondary system borrows its air from the primary tank
- C. The two systems draw from one shared air tank

Answer: A. The two halves of a dual system are fully separate. Each one has its own air tanks, hoses and lines, so a failure in one does not drain the other. A shared tank would defeat the point of having two systems, and the secondary system does not feed off the primary tank.
Source: CDL Manual (AAMVA model, March 2025), Section 5.2 Dual Air Brake, “”

## 8. After coupling a ball-type drawbar, part of the coupling ball can still be seen. What should you do about it?
- A. Wrap the exposed part with tape to keep out dirt
- B. Fit the rubber bellows cover over it and anchor its edge on the ball
- C. Leave it open so you can check the joint during trips

Answer: B. The exposed part of the ball gets covered with the rubber dust-proof bellows, and its edge must be anchored right onto the ball. Leaving it bare lets dirt get into the joint. Tape is not the protective cover the procedure calls for.
Source: CDL Manual (AAMVA model, March 2025), Section 6.4.5 Coupling a Drawbar, “”

## 9. You are pulling a loaded trailer when it breaks loose and tears the emergency air hose apart. What happens to the trailer's brakes?
- A. The trailer brakes fully release
- B. The trailer emergency brakes come on
- C. The trailer brakes work only from the hand valve

Answer: B. When the emergency line loses its air, the trailer's emergency brakes apply. That is the built-in safety feature for a breakaway. The brakes do not release, and the hand valve cannot control them, because the hand valve sends air through the service line.
Source: CDL Manual (AAMVA model, March 2025), Section 6.2.4 Trailer Air-lines, “”

## 10. During your pre-trip inspection, you want to find the trailer's yellow ABS malfunction lamp. Where should you look?
- A. On the right side, at the rear corner only
- B. On the left side, at the front or rear corner
- C. At the center of the rear, above the doors

Answer: B. Trailer ABS malfunction lamps are yellow and are mounted on the left side of the trailer, at either the front or the rear corner. They are not placed on the right side or in the middle of the rear end.
Source: CDL Manual (AAMVA model, March 2025), Section 6.3.1 Trailers Required to Have ABS, “”

## 11. You have just adjusted the trailer to the right height. What else should you check before hooking up the air lines?
- A. That the fifth wheel slider has been unlocked
- B. That the kingpin and fifth wheel are lined up
- C. That the trailer brakes have been released

Answer: B. Once the height is right, confirm that the kingpin lines up with the fifth wheel so the jaws can catch it. The trailer stays held by its chocks or spring brakes at this point. A sliding fifth wheel should be locked, not unlocked.
Source: CDL Manual (AAMVA model, March 2025), Section 6.4.1 Coupling Tractor-Semitrailers, “”

## 12. You have stopped the tractor with its frame still under the trailer and secured it. What do you go back to check?
- A. That the trailer air tank still shows full pressure
- B. That the fifth wheel jaws closed back around the kingpin
- C. That the ground holds the trailer and the landing gear is intact

Answer: C. Before you drive fully away, confirm the ground is truly carrying the trailer and the landing gear isn't bent or broken. The fifth wheel is already out from under the trailer, so its jaws are no longer on the kingpin. Tank pressure is not what tells you the trailer is safely supported.
Source: CDL Manual (AAMVA model, March 2025), Section 6.4.2 Uncoupling Tractor-Semitrailers, “”

## 13. This week you drive three rigs. One has ABS on the tractor only, one on the trailer only, and one on both. How should your braking change from rig to rig?
- A. Brake harder in the rig with full ABS
- B. Brake the same way in all three rigs
- C. Brake lighter in the rig with tractor ABS

Answer: B. Which units have ABS does not change how you brake. Use the same technique in every rig: only the force needed to stop safely while staying in control. Full ABS is no reason to brake harder. Tractor-only ABS does not call for a lighter touch either.
Source: CDL Manual (AAMVA model, March 2025), Section 6.3.2 Braking with ABS, “”

## 14. You have coupled and connected the lines, and you are cranking up the landing gear. How far should you raise it before you drive?
- A. Only until the pads just clear the pavement
- B. All the way up, then secure the crank handle
- C. About halfway, so it can be lowered quickly

Answer: B. Raise the landing gear fully and secure the crank handle. Landing gear left partly down can catch on railroad tracks or other objects. Raising it only a little or halfway is not enough.
Source: CDL Manual (AAMVA model, March 2025), Section 6.4.1 Coupling Tractor-Semitrailers, “”

## 15. Partway through your trip, the trailer's ABS malfunction lamp comes on and stays lit. What is the right action?
- A. Stop at once, because the trailer has lost its brakes
- B. Brake with extra force from now on to make up for ABS
- C. Keep driving normally and have the ABS serviced soon

Answer: C. ABS is added on top of your normal brakes. When it fails, your regular brakes still work. Drive normally and get the system repaired soon. ABS does not add stopping power, so you do not need extra brake force, and the trailer has not lost its brakes.
Source: CDL Manual (AAMVA model, March 2025), Section 6.3.2 Braking with ABS, “”
